St. Peters University
The Distance Education programmes are offered from the academic year 2009-2010. The system of Distance Education includes openness and flexibility to a greater extent. It is open to all adults in india.
Years1
Working and Characteristics of Junction diode ,Zener diode and tunnel diode. Working of IMPATT diode, PIN diode . Construction and V-I characteristics of thermistors, Gunn effect diode, Varactor diode, Photoconductive devices - Photoconductive cells, photo diodes, LED, Solar Cells - MEMS and Nano Technology
Unit -II
Construction – operation and Characteristics of a Bipolar transistor- biasing of a transistor – base bias, collector to base bias and self bias-. Causes of shift of Quiescent operating point. Stability factor- Hybrid parameters- Construction , operation and Characteristics of SCR, UJT, JFET and MOSFET - Biasing of JFET- Multivibrators.
IC Fabrication: classification –fundamentals of monolithic IC technology – basic planer processes: Silicon wafer preparation – Epitaxial growth – Oxidation – photolithography – Diffusion – Isolation – Metallization – monolithic transistors – monolithic diodes – integrated resistors – integrated capacitors – thin and thick film technology
Digital IC’s: Basic terms related to digital IC’s – RTL and DTL circuits – Integrated Injection logic - TTL – Open collector output – Totem pole output – Schottky TTL gate – ECL – MOS – CMOS.
Designing of OPAMP circuits: OPAMP as Comparator – OPAMP as zero crossing detector – Constant current source – current to voltage converter – thermocouple – temperature monitor – strain gages –force measurement
1. Electronic Devices and Circuits by G.K.Mithal
2. Electronic devices : Applications and Integrated circuits by Mathur,
Kulshreshtha and Chandha
3. D. Roy Choudhury and Shail Jain “Linear Integrated Circuits” New
age International Ltd, New Delhi 1997
UNIT-I
Evolution of Microprocessor – Typical Micro Computer Architecture – Memory –memory addressing - Timing diagram -Input/Output .
UNIT – II
Intel 8085: Introduction – Register Structure- block diagram – 8085 Addressing modes – Timing Methods- 8085 CPU pins and Associated Signals – instruction set- – Interrupt System – SID and SOD Lines – 8085 Based System Design.
UNIT – III
Interfacing Devices: Introduction – Types of Interfacing Devices – Addressing Decoding for I/O – Input/Output Ports – Programmable Interrupt Controller 8259 – Programmable DMA Controller: 8257 Programmable DMA Controller – Analog Input Devices – Analog Output Devices.
UNIT – IV
16-bit Microprocessor: Intel 8086:Introduction – Architecture – Addressing Modes – 8086 Input/Output. Motorola MC 68000:Introduction – Registers – Memory Addressing – Instruction Format – Addressing modes – Motorola 68000 I/O
UNIT - V
Introduction- register set- Continuous architecture- addressing modes of 80286-
Pentium processor
Introduction- register set- block diagram -addressing modes- pipelining- integer pipelining- floating pipelining.
REFERENCE BOOKS:
1 M.Rafiquzzaman, “Microprocessors Theory and Applications : Intel
and Motorola”, Prentice Hall India, Revised Edition, 2004.
2. Aditya P. Mathur, “Introduction to Microprocessors”, Tata McGraw
Hill, Third Edition, 1990.
3. R.S.Gaonkar, “Microprocessor Architecture,programming and
Applications with the 8085”, 1995.
4. M.Rafiquzzaman, “Microprocessor and MicroComputerBased System
Design”,UBS, 1995.
5. Advanced microprocessor – Mc graw Hill-Daniel Tabak
UINT-I: Pulse modulation System:
Introduction to pulse Modulation – Types – Sampling theorem-Pulse- Width modulation-Generation and demodulation of (PEM)-Pulse position modulation (PPM). Pulse code modulation-Principles-Effects of noise-Companding-Advantages and applications of PCM-Differential PCM-Delta modulation.
UINT-II: Digital modulation techniques:
Digital carrier systems-Amplitude shift keying-Frequency shift keying-Phase shift keying (PSK)-Binary phase shift keying (BPSK)-Carrier recovery circuits- Differential phase shift keying (DPSK)-Hard and soft decision decoders.
UINT-III: Fiber optic cables:
Optical fiber cables-Fiber strength and durability-Stability of the fiber transmission characteristics:-Micro bending-Hydrogen absorption-Nuclear radiation exposure-Cable design; fiber buffering-Cable structured and strength members-Cable sheath and water barrier-Example of fiber cables.
UINT-IV: Light sources and light detectors:
Light sources: LED structure-Planar LED, dome LED, Surface emitter LEDs-Edge emitter LEDs-Super luminescent LEDs-LEDs reliability.
Light detectors: mid-Infrared photodiodes-Phototransistors-Photoconductive detectors.
UNIT-V: Fiber optical communication components and systems:
Components: coupling components for optical fibers-Modulation methods and modulators-Switches-Transmitters-Receivers-Optical amplifiers (Semiconductor Laser Amplifiers). Systems: transmitter and receiver design-Link design-Link codes for optical fiber links.
Text and reference books:
Thyristor : Introduction – natural commutation – forced commutation –self commutation – impulse commutation – resonant pulse commutation – complementary commutation - external pulse commutation.
Unit-II:
Controlled rectifiers:- Introduction – principles of phase controlled converters – single-phase semi converters – single-phase full converters – single-phase dual converters – single-phase series converters.
Static switches:- Introduction – single phase AC switches – three phase AC switches – three phase reversing switches - AC switches for Bus transfer – solid state relays.
AC voltage controller:- Introduction – Principles of ON - OFF control – principle of phase control – single phase bidirectional controllers with resistive loads and inductive loads– single phase cyclo converters-UPS.
Unit-IV: VLSI FABRICATION TEHNIQUES
An overview of wafer fabrication – Wafer processing – Oxidation – Patterning – Diffusion – Ion implantation – Deposition – Si gate n MOS process – C MOS process – n well – p well Twin tub – Si on insulator – C MOS process Enhancement – Interconnection circuit elements.
UNIT- V: INTRODUCTION TO VHDL
Overview of VHDL – Capabilities – Hardware device – Basic terminology – Entity declaration. ARCHITECTURE BODY : Structure style of modeling – Data flow – Style of modeling – Behavioral style of modeling – Mixed style of modeling – Configuration declaration – Package declaration.
1. Rashid M.H “ Power Electronics: Circuits Devices and Application” 2nd Edition PHI New Delhi 1996.
2. Timothy J. Maloni: Industrial solid state electronic devices and circuits” 2nd Ed., 1986.
3. Neil H.E. Weste Kamaran Eshraghian, “PRINCIPLES OF CMOS VLSI DESIGN”.
4. J. Bhasker, “VHDL Primer”, Low Price Edition, 2001
5.Charles H. Roth, Jr. “DIGITAL SYSTEM DESIGN USING VHDL”, Brooks/Cole Thomson Learning PWS Publishing, ISBN-981-240-052-4.
1. Full wave and bridge rectifiers.
2. Clipping and clamping circuits.
3. CE amplifier design.
4. CS FET amplifiers design.
6. Colpitts oscillators.
7. Hartley oscillator.
8. Wien bridge oscillator.
9. Phase shift oscillator.
10. Multivibrators using transistors.
11. Verification of Demorgan’s theorem
12. Half and Full Adder,
13. Half and Full subtractor
14. Multiplexer
15. De-multiplexer
16. Encoder and Decoder
17. Shift Register
18. Decade and UP/DOWN counter
19. Analog to Digital Counter
20. Single phase inverter
Years2
Unit-I: Telecommunication system:
GSM-mobile services – system architecture – radio interfaces – protocols –localization and calling – hand over and security-new date services.
DECT- system architecture – protocol architecture –TETRA-UMTS and IMT2000- UMTS releases and standardization- UMTS architecture –UMTS radio interface – Hand over.
Unit –II:
GEO- LEO-MEO –routing localization- hand over.
Wireless LAN: Infrared and radio transmission-infrastructure and ad-hoc network-IEEE802.11- HIPERLAN – blue tooth.
Unit –III:
Mobile and ad- hoc networks – routing –destination sequence distance vector- dynamic source routing – alternative matrices.
Unit – IV:
Mobile transport layer ;
Traditional: congestion control – slow start- fast retransmit/ fast recovery- implication of mobility. Classification of TCP improvements : indirect- snooping- mobile TCP-fast transmission /receiving- transmission/time out frequency-selective retransmission
Unit-V:
File system: consistency –coda-little work-ficus – Mio-NFS-recover.
WAP: Architecture-Wireless datagram protocol-transmission layer security-transaction protocol- session protocol- application environment.
Reference books
1. Mobile communication – 2 nd edition –Schiller – Pearson.
2. Wireless communication networks - William Stellys – Low price edition
Pearson Edu.
1. Wireless and Mobile Circuits – JACKM HOLTZMAN, DAVIDJ.GOODMAN –
Allied publication.
Unit-I:
Internet working: principles of internet working – concatenated virtual circuits – connection less internetworking – tunneling- internetwork routing-fragmentations- firewall.
The www: the client side – the server side – writing a web page in HTML – locating information on the web.
The internet transport protocol(TCP and UDP): the TCP service model-TCP protocol-TCP segment header-TCP connection management – TCP transmission policy –TCP congestion control – TCP time management – UDP-wireless TCP and UDP.
ISDN: the integrated digital network- overview of ISDN-transmission structure-user access-ISDN protocols.
BROAD BAND ISDN: NTI,-NTI plus and voice communication basis: terminating ISDN connections via NTI- Basis OF NTI and NTI plus- theISDN voice communication primer.
B-ISDN: Introduction- the current situation- the idea of the ISDN-B-ISDN- ATM based service and applications- B-ISDN- service and applications initial ATM network services
Desktop video conference: The down sizing of video conference-desk top video conferencing systems- video conferencing requirements-leading desktop video conferencing systems- elements of video conferencing style.
Reference books:
Basic Concepts of OOP – Structure of C++ - Data types - Variables – Control Structures – Functions – Classes and Objects – Constructors and Destructors.
Overloading: Function, Operator – Inheritance – Pointers – Virtual Function – Polymorphism.
Streams in C++ - Stream Classes – Formatted and Unformatted data – Manipulators – User Defined Manipulators – File Streams – Opening and Closing a File – File Pointers Manipulation – Template Classes and Functions – Exception Handling: Try, Catch, Throw.
UNIT-IV: Introduction to Java – Features of Java – Methods and Classes – Array, Strings and Vector – Inheritance – Packages and Interfaces.
UNIT-V:
Exception Handling – Multithreading – Applets – Graphics Pogramming.
1. E.Balagurusamy, “Object Oriented Programming with C++”, TMH, Second Edition, 2001.
2. Ravichandran, “Programming with C++”, TMH, 1996.
3. Bjarne Stroustrup, “The C++ Programming Language”, Addision Wesley, 2004.
4. Patrick Naughton and Hilbert Schildt, “The Complete Reference
Java 2”, TMH, 2003.
4. E.Balagurusamy, “Programming with Java A Primer”, TMH, Second
Edition, 1999.
Using 8085:
1. AM modulation
2. FM modulation and detection
3. Automatic gain control
4. Voltage gain control
5. Pulse amplitude modulation
6. Pulse width modulation
7. Pulse position modulation
8. Study of PLL characteristics
9. Digital phase detector
10. Pulse code modulation
11. Study of cable TV system
12. Microwave experiments – Klystron
The topic of the Project shall be assigned to the candidate before the end of first year and a copy of the same should be submitted to the University for approval.
Each guide shall have a maximum of five students in science and maximum of seven for all Arts subjects.
There will be an advisory committee consisting of the guide as chairman and one member from the same department or allied departments of the college and a third member should be from other college preferably from Aided / Government colleges in the case of self financing college and vice – versa.
c. No. of Copies/ Distribution of Project
The students should prepare three copies of Project and submit the same for the evaluation by examiners. After evaluation one copy is to be retained in the college library and one copy is to be submitted to the University (Registrar) and one copy can be held by the student.
d. Format to be followed
The formats / certificate for Project to be submitted by the students are given below:
Format for the preparation of project work
a. Title page
b. Bonafide certificate
c. Acknowledgement
d. Table of content
CONTENTS
CHAPTER NO.
TITLE
PAGE NO
1.
Introduction
2.
Review of literature
3.
Materials and methods
4.
Results
5.
Discussion
6.
Summary
To buy books pls click on the link below:
Copyright © 2013 - All Rights Reserved - Distance-edu.co.in Google
Powered by Nasbar Infotech